混凝土三轴等幅拉-压疲劳性能试验研究

Fatigue tests were conducted on tapered plain concrete prism specimens under triaxial constant-amplitude tension-compression cyclic loading. The low stress of the cyclic loading was taken as 0.2fc and the upper stress ranged from 0.20ft to 0.65ft. Three constant lateral pressures were 0.1fc, 0.2fc and 0.3fc respectively. Based on the results, the three-stage evolution nile of the fatigue stiffness, maximttm(minimum) longitudinal strain and damage were analyzed, and a unified S-N curve to calculate fatigue strength factors was worked out. The results show that the fatigue strength and fatigue life under triaxial constant-amplitude tension-compression cyclic loading are smaller than those under uniaxial fatigue condition. Moreover, the secondary strain creep rate is related to the fatigue life, a formula for describing their relation was derived. The investigation of this paper can provide information for the fatigue design of concrete structures.     

Three-dimensional nonlinear analysis of creep in concrete filled steel tube columns

INTRODUCTION Creep is an internal characteristic of concrete under long-term load. A long time has elapsed since the first discovery of concrete creep in 1907 by Hatt. Many researches have been devoted to this complex problem ever since. However, despite major suc-cesses, the creep phenomenon is still far from being fully understood, even though the phenomenon has occupied some of the best minds in the field, such as Glanville, Dischinger, Troxell, Pickett, Neville, etc. Creep phenome…     

改进的新老混凝土粘结约束收缩计算模型研究

引入增量法,提出了改进的新老混凝土粘结约束收缩力学模型。根据相关的实验结果论证该约束收缩力学模型的有效性。最后利用改进的模型对新浇筑自密实混凝土截面上的应力分布情况以及粘结面上的约束剪力进行计算,并对结果进行分析。分析表明,自密实混凝土比普通混凝土因收缩而产生的应力更大,尤其在早龄期;收缩应力不仅会在很大程度上受到自由收缩的影响,而且与混凝土的基本物理力学性能有关。     

Shrinkage behavior of self-compacting concrete

In the structures where long-term behavior should be monitored and controlled, creep and shrinkage effects have to be included precisely in the analysis and design procedures. Shrinkage varies with the constituent and mixture proportions, and depends on the curing conditions and the work environment as well. Self-compacting concrete (SCC) contains combinations of various components, such as aggregate, cement, superplasticizer, water-reducing agent and other ingredients which affect the properties of the SCC including shrinkage. Hence, the realistic prediction shrinkage strains of SCC are an important requirement of the design process for this type of concrete structures. This study reviews the accuracy of the conventional concrete (CC) shrinkage prediction models proposed by the international codes of practice, including CEB-FIP (1990), ACI 209R (1997), Eurocode 2 (2001), JSCE (2002), AASHTO (2004; 2007) and AS 3600 (2009). Also, SCC shrinkage prediction models proposed by Poppe and De Schutter (2005), Larson (2007), Cordoba (2007) and Khayat and Long (2010) are reviewed. Further, a new shrinkage prediction model based on the comprehensive analysis on both of the available models, i.e., the CC and the SCC is proposed. The predicted shrinkage strains are compared with the actual measured shrinkage strains in 165 mixtures of SCC and 21 mixtures of CC.     

蠕变条件下完整岩石的起裂和扩展准则

The mechanism and criterion of crack initiation and propagation of rocks were investigated by many researchers,And the creep behaviour of rocks was also theoretically and experimentally studied by some scientists and engineers.The characteristics of crack initation and propagation of rocks under creep condition.however,are very improtant for rock engineering and still not paid enough attention by researchers,In this paper,the criterion and mechanism of crack initiation and propagation under creep condition were investigated using specimens collected from sandstone rock formations outcropping in the Emei Mountain,the Sichuan Province of China.Cuboid specimens under three point bending were used in this investigation.All specimens were classified into four sorts and used for Mode-I fracutre of creep frcture tests.The experimental result shows that due to creep deformation.rock crack will inevitably initialt and propagate under a load of KI,which is less than fracture toughness KIC but not less than a constant(marked as KIC2),KIC2 indicates the ability of rock to resist crack initiation and propagation under creep conditions and is less than fracture tough ness KIC.defined as creep fracture toughness in this paper,KIC2 should be considered as an importnat parameter on design and computation of rock engineering.The microstructureal mechanism for crack initiation and propagation of rock materials under creep condition was introduced based on competitive model between softening effect and hardening effect,and the validity of test result was explained.The test result was also verified in rheological theory.When KI is more than KIC2 but less than KIC,rock crack will initiate and propagate after a time interval of sustained loading under creep condition.In order to find the relation between duration of sustained lading.which can lead to crack initiation and propagation,and the initial stress intensity factor KI,an unequal0interval time sequence forecasting and predicting model was introduced,and the relation was obtained for homogeneous and isotropic fine-grained red sandstone.Finally a modified fracture toughness formula was given,in which the influence of fracture process zone(FPZ) was fully considered.     

再生混凝土力学性能的研究

对再生混凝土力学性能的研究进行了综述，主要包括再生混凝土力学性能的抗压强度、弹性模量、干缩与徐变。研究表明，和普通混凝土相比，再生混凝土力学性能的抗压强度低，弹性模量小，干缩与徐变较大。最后提出了再生混凝土力学性能需要进一步研究的问题。     

建筑现浇板上下贯穿裂缝应力分析控制

分析建筑现浇板由混凝土收缩和温差共同作用引起上下贯穿裂缝的产生机理,通过微元体建立建筑外周粱与室内板间的静力平衡关系,导出以混凝土极限收缩应变值ε反映混凝土材料质量影响的外梁温差应力计算公式,提出建筑现浇板预控贯穿裂缝的强度计算式及施工过程与使用过程的预控措施.     

拓宽工程新建桥梁上部结构混凝土收缩对结构受力影响分析

就某高速公路拓宽桥梁新建上部结构混凝土收缩对结构受力的影响进行分析。介绍混凝土收缩的机理、主要原因和影响因素,结合工程实例,建立有限元模型,计算分析混凝土收缩对T形梁结构受力的影响,为拓宽桥梁的优化设计和施工提供理论依据。     

In-plane creep buckling of concrete-filled steel tubular arches

The creep-induced deformation of the arch rib of concrete-filled steel tubular （CFST） arches under a sustained load can increase the bending moment, which may lead to earlier stability failure called creep buckling. To investigate the influences of concrete creep on the buckling strength of arches, a theoretical analysis for the creep buckling of CFST circular arches under distributed radial load is performed. The simplified Arutyunyan-Maslov （AM） creep law is used to model the creep behavior of concrete core, and the creep integral operator is introduced. The analytical solutions of the time-dependent buckling strength under the sustained load are achieved and compared with the existing formula based on the age-adjusted effective modulus method （AEMM）. Then the solutions are used to determine the influences of the steel ratio and the first loading age on the creep buckling of CFST arches. The results show that the analytical solutions are of good accuracy and applicability. For CFST arches, the steel ratio and the first loading age have significant influences on creep buckling. An approximate log-linear relationship between the decreased degrees of the creep buckling strength and the first loading age is found. For the commonly used parameters, the maximum loss of the buckling strength induced bv concrete creen is close to 40%     

Experimental study of lightweight aggregate concrete under multiaxial stresses

Lightweight aggregate concrete cube specimens (100 mm×100 mm×100 mm) and plate specimens (100 mm×100 mm×50 mm) were tested under biaxial compression-compression (CC) and compression-tension (CT) load combinations. For comparison, normal concrete plate specimens (100 mm×100 mm×50 mm) were tested under the same load combinations. Based on the test results, a two-level strength criterion of lightweight aggregate concrete in both octahedral stress coordinate and principal stress coordinate was suggested. The lightweight aggregate concrete cube specimens (100 mm×100 mm×100 mm) were then tested under triaxial compression-compression-compression (CCC) load combination with corresponding tests on normal concrete cube specimens (100 mm×100 mm×100 mm). The effect of intermediate principal stress on triaxial compressive strength is further examined. A "plastic flow plateau" area was apparent in principal compressive stress-strain relationships of lightweight aggregate concrete but not in normal concrete. A quadratic formula was suggested for the expression of strength criterion under triaxial compression.     

高应力比下路用水泥混凝土疲劳可靠度量化分析(英文)

为获得路用水泥混凝土在高应力比作用下其疲劳可靠度的变化规律,首先推导了包括混凝土疲劳寿命在内的单调随机变量的概率密度,然后推导了 Miner 与 Chaboche-Zhao 疲劳损伤模型的概率密度. 借助室内疲劳试验结果,获得这 2 种模型的疲劳损伤概率密度函数. 最后,将荷载作用次数代入上述函数,从而获得水泥混凝土疲劳可靠度随荷载作用次数的变化规律. 结果表明: 随着荷载作用次数的增加,相同应力比下,疲劳可靠度从 100%逐渐衰减为 0%; 无论何种应力比,在荷载作用初期,疲劳可靠度均有一个较为稳定的阶段; 随着应力比的增加,该稳定阶段逐渐缩短,且可靠度为 0%时对应的荷载作用次数也减小; 在可靠度衰减阶段,对于相同荷载作用次数,应力比越高,则混凝土可靠度越低; 此外,Miner 疲劳损伤模型比Chaboche-Zhao 疲劳损伤模型偏安全.     

Predicting unstable toughness of concrete based on initial toughness criterion简

The fracture processes of concrete were described by a cohesive crack model based on initial toughness criterion. The corresponding analytical method to predict the instability state was proposed. In this model, the initial toughness was adopted as the crack propagation criterion and the weight function method was used to calculate the stress intensity factor and the crack opening displacement caused by the cohesive stress. The unstable toughness can be easily obtained using the proposed method without measuring parameters at the critical state that was necessary in traditional methods. The proposed method was verified by existing experimental data of wedge splitting specimens with different grades of concrete and the sensitivity of the results on the tensile softening curve was discussed. The results demonstrate that the proposed method can well predict the peak load, the critical effective crack length, and the unstable toughness of concrete specimens. Moreover, the calculated unstable toughness is not sensitive to the tensile softening curve.     

Bending Resistance of Steel Plate-Reinforced Concrete Beam

The formulas for calculating bending-resistant capacity of a steel plate-reinforced concrete composite beam are derived. To validate the formulas, experiments of the composite beam under three-point bending are carried out. Calculated results based on the formulas are in good agreement with experimental results.     

大骨料混凝土在双轴压应力状态下的变形和强度试验研究

利用大连理工大学自行研制改造的液压伺服静、动态三轴试验系统对不同骨料级配和尺寸的混凝土试件在双向压荷载作用下的变形和强度特性进行了试验研究.试验所用试件有3种:采用大坝原级配最大骨料粒径为80 mm的立方体试件以及相应的湿筛混凝土试件,尺寸分别为250mm×250mm×250 mm,150 mm×150 mm×150 mm和100 mm×100 mm×100 mm.试验过程中,测得了所有试件两个加载方向的应力和应变,以及未加载方向上的侧向变形,并根据试验结果,系统地探讨了不同级配混凝土的双轴抗压强度、极限变形、应力-应变曲线以及破坏形态的变化规律,发现大骨料混凝土在双轴压作用下的极限强度和变形能力要比相应的湿筛小骨料混凝土提高的更多,最后分别在主应力空间和主应变空间建立了不同级配混凝土的破坏准则,这为水工大体积混凝土按多轴强度理论进行设计提供了试验依据.     

超长钢筋混凝土框架结构温度裂缝控制

以纵向长度为126．5m的钢筋混凝土框架结构教学楼为例,采用通用有限元软件SAP2000为分析工具,综合考虑几何非线性、收缩应力、徐变效应等因素,得到全楼的温度应力,并在设计及施工过程中对薄弱部位进行加强,总体取得较好的成效,保证了建筑效果的表现,表明该分析方法的精度能满足工程应用的要求,并具有一定的可靠性。     

高性能混凝土配合比设计正交试验研究

运用正交试验设计法对高性能混凝土的配合比进行试验，研究了水泥、粉煤灰、矿渣和水胶比四个因素对高性能混凝土抗压强度的影响，找出了其中显著的影响因素：根据试验结果，进行线性回归，给出了预测模型。     

高强混凝土墙耐火性能的有限元分析

确定了钢材和混凝土热工参数和热一力本构关系,采用ABAQUS软件建立了火灾下高强混凝土墙温度分布和受力性能分析的有限元模型,计算结果得到以往实验结果的验证.在此基础上,对高强混凝土墙高温下的应力分布、混凝土裂缝以及重要影响因素进行了分析,初步了解了火灾下高强混凝土墙的力学性能,为进一步确定科学合理的抗火设计方法创造了条件.     

混凝土单轴压缩应力状态的数值分析

以测试混凝土抗压强度的试件为数值分析对象,模拟混凝土试件抗压强度的广义荷载,分析了混凝土试件在其标准抗压强度下的应力场,提出了一个混凝土试件破坏强度的概念。     

钢筋混凝土薄板破坏类型的判别

论述了钢筋混凝土薄板在两个平面内正应力和一个剪应力作用下的几种破坏类型，解释了破坏类型图的含义，给出了其计算过程，计算结果与试验结果吻合较好，并指出了其它文献中存在的不合理之处。     

Unified expression for failure of reinforced concrete members in bridge

INTRODUCTION Reinforced concrete elements with box section are commonly used in horizontal subsystems and in vertical support of bridge structures. The horizontal structural members normally have box section and top flange. The vertical supports of the bridge usually have a box section also. To simplify the deduction of such structural member under combined forces, the box sections without top flange are discussed here. Fig.1 shows the typical section types of reinforced concrete members.…