共查询到18条相似文献,搜索用时 140 毫秒
1.
表面粗糙度对装备,特别是高精密装备影响非常大。找出降低表面粗糙度的方法,一直是机械加工生产相关人员的不懈追求。本文通过表面粗糙度产生的原因及控制措施来阐述表面粗糙度,以期能经济有效地降低表面粗糙度。 相似文献
2.
3.
电火花加工的表面粗糙度值直接影响工件的使用性能,如耐磨性、配合性能、接触刚度、疲劳强度和耐腐蚀性等。电火花加工粗糙度值的影响因素可分为电参数和非电参数两大类,电规准中对表面粗糙度影响较为显著的是脉冲宽度,工件材料的性质也会对加工表面粗糙度产生影响。 相似文献
4.
机械加工影响表面粗糙度的因素及改善措施探讨 总被引:1,自引:0,他引:1
表面粗糙度是衡量机械加工是否合格的重要指标,表面粗糙度对于所加工零件的耐磨性、运动精度、质量以及工作寿命都有着非常显著的影响,现今机械加工零件的表面粗糙度没有得到有效的保障,这对零件的质量造成了较大的影响,所以针对这种情况就需要对其进行改善,本文将详述机械加工影响表面粗糙度的因素及其改善措施。 相似文献
5.
在机械零件图上,标注表面粗糙度是必不可少的。但是AutoCAD绘图软件没有标注表面粗糙度的功能。若要用AutoCAD来绘制零件图,用户必须自行解决表面粗糙度的标注问题。介绍了在AutoCAD中用带有属性的图块,把表面粗糙度数值定义为可变属性进行插入来标注表面粗糙度的方法.,不仅提高了标注效率,而且使图形符号的标注规范统一。 相似文献
6.
7.
8.
9.
一、引言用车、铣、刨等切削加工方法形成的加工表面是由方向性很强的加工纹理所组成。其表面粗糙度一般用轮廓的平均算术偏差Ra或微观不平度+点高度Rz来评定。通常以Ra为主。电火花加工表面由于没有专门测试仪器,故也使用Ra作为表面粗糙度的评定参数。由于电火花加工与切削加工的加工原理不同,所以加工后工件表面微观形貌也不大一样,这样沿用切削加工表面粗糙度的测试方法和评定参数来评价电火花加工表面粗糙度是否科学是一个值得探 相似文献
10.
11.
高能气动喷丸是通过剧烈塑性变形产生细晶材料的方法之一.用纯铜作为实验材料在高能气动喷丸实验机上作喷丸实验,利用表面形貌仪、显微硬度仪以及电子背散射衍射方法对经喷丸处理的试样进行表面粗糙度、硬度及晶粒尺度的测量.结果表明,表面粗糙度随处理时间的增长呈指数衰减趋势;晶粒尺度细化了一个量级,由初始的25.48μm细化至252μm;且显微硬度由原来的058GPa增加到125GPa.量纲分析得到喷丸过程的5个无量纲参数,利用有限元模拟研究了无量纲参数的影响.自编制程序产生丸粒的随机碰撞并调用Ansys?ls dyna模拟碰撞过程,并将模拟1000次碰撞的结果与相应的实验值进行了比较. 相似文献
12.
大风天气下北京城市边界层阵风结构特征 总被引:14,自引:0,他引:14
通过分析北京 32 5米气象塔风温观测资料,研究了大风天气条件下北京城市地区大气边界层特征。发现在大风天气条件下北京城市大气边界层阵风结构存在如下规律:(1 )大风条件下,对数风廓线规律可适用到 1 5 0m的高度,主要是因为城市下垫面的地面粗糙度较大,使得大风与地面粗糙元素之间的相互作用加强;(2 )阵风系数在地面附近较大,随高度呈负指数函数形式递减;(3)阵风强度随高度也呈负指数函数形式递减,但其递减率要小于阵风系数的递减率。 相似文献
13.
This paper reviews our work on the application of ultrafast pulsed laser micro∕nanoprocessing for the three-dimensional (3D) biomimetic modification of materials surfaces. It is shown that the artificial surfaces obtained by femtosecond-laser processing of Si in reactive gas atmosphere exhibit roughness at both micro- and nanoscales that mimics the hierarchical morphology of natural surfaces. Along with the spatial control of the topology, defining surface chemistry provides materials exhibiting notable wetting characteristics which are potentially useful for open microfluidic applications. Depending on the functional coating deposited on the laser patterned 3D structures, we can achieve artificial surfaces that are (a) of extremely low surface energy, thus water-repellent and self-cleaned, and (b) responsive, i.e., showing the ability to change their surface energy in response to different external stimuli such as light, electric field, and pH. Moreover, the behavior of different kinds of cells cultured on laser engineered substrates of various wettabilities was investigated. Experiments showed that it is possible to preferentially tune cell adhesion and growth through choosing proper combinations of surface topography and chemistry. It is concluded that the laser textured 3D micro∕nano-Si surfaces with controllability of roughness ratio and surface chemistry can advantageously serve as a novel means to elucidate the 3D cell-scaffold interactions for tissue engineering applications. 相似文献
14.
风能资源评估中地表粗糙度的研究 总被引:1,自引:0,他引:1
利用内蒙东部草原接近1年4层风速廓线资料,采用最常用的两类方法(拟合对数风廓线法和Davenport土地类型系统划分法),结合风能资源利用的特点,来估算该地区地表粗糙度长度。选取10分钟平均风速50m高度大于6m/s时刻的数据,因为50m高度平均风速6m/s以下的时,轮毂高度为80m的风机只能产生少量不稳定的风能。这样挑选数据能够有效地减少粗糙度长度评估中的离散范围。拟合对数风廓线,发现该地区地表粗糙度长度有明显月份和季节变化,夏秋植被茂盛期和冬春植被枯萎期粗糙度长度分别为0.138m和0.088m;细微的地形起伏也会对粗糙度的评估造成影响。两类方法估算的粗糙度长度大致相当,且估算的风能密度只相差2%左右。Davenport法对比较平坦的地形进行粗糙度评估,具有一定的应用参考价值。 相似文献
15.
黄土高原低山丘陵区农村居民点分布与地形因子关系研究——以兰州市七里河区为例 总被引:12,自引:1,他引:11
选取黄土高原低山丘陵区的兰州市七里河区农村居民点为研究对象,以ArcGIS9.3软件为技术平台,基于研究区DEM提取研究区高程、坡度、坡向、地形起伏度、地表粗糙度、坡度变率、坡向变率、地表切割深度和地形高程变异系数9个地形因子,在对9个地形因子进行分级分析后,应用分布指数以及信息熵计算分析了地形因子与农村居民点分布格局的关系.结果表明,研究区农村居民点在各地形位上分布的优势地形位分别为:高程1 500~1 750m和1 750~2 000m的地区,坡度0~5°、5~10°和10~15°的地区,坡向W、S、SW的地区,地形起伏度0~50m和50~100m的地区,地表粗糙度1~1.1的地区,坡度变率0~5°的地区,坡向变率10~15°和15~20°的地区,地表切割深度0~10m的地区,地形高程变异系数0~0.003的地区.同时,在各优势地形位上农村居民点的分布呈现出相对较高的有序性,这体现了农村居民点分布格局与地形因子关系的高度关联性. 相似文献
16.
Replica obtained from micromolds patterned by simple photolithography has features with uniform heights, and attainable microchannels are thus quasi-two-dimensional. Recent progress in three-dimensional (3D) printing has enabled facile desktop fabrication of molds to replicate microchannels with varying heights. We investigated the replica obtained from four common techniques of 3D printing—fused deposition modeling, selective laser sintering, photo-polymer inkjet printing (PJ), and stereolithography (SL)—for the suitability to form microchannels in terms of the surface roughness inherent to the mechanism of 3D printing. There have been limited quantitative studies that focused on the surface roughness of a 3D-printed mold with different methods of 3D printing. We discussed that the surface roughness of the molds affected (1) transparency of the replica and (2) delamination pressure of poly(dimethylsiloxane) replica bonded to flat glass substrates. Thereafter, we quantified the accuracy of replication from 3D-printed molds by comparing the dimensions of the replicated parts to the designed dimensions and tested the ability to fabricate closely spaced microchannels. This study suggested that molds printed by PJ and SL printers were suitable for replica molding to fabricate microchannels with varying heights. The insight from this study shall be useful to fabricate 3D microchannels with controlled 3D patterns of flows guided by the geometry of the microchannels. 相似文献
17.
在三轴曲面加工中,曲面加工质量与刀位轨迹的质量有紧密联系。在使用当前的计算机辅助设计(CAD)/计算机辅助制造(CAM)集成软件生成刀位轨迹时,若仅采用通常的0.01mm公差,在加工时有可能出现表面凹坑、光洁度较差等缺点。为解决上述问题,提出一种基于网格均匀化的刀位轨迹优化方法,在Cimatron生成的加工刀位轨迹基础上,通过建立主导轮廓线并对不规则的点进行修正来降低相邻刀路倾斜度变化的程度;然后对同一条刀路上的刀位点进行光滑连续直线段的识别;再采用分段3次样条进行拟合,以提高同一刀路上的曲线光滑程度。仿真实验与实际加工实验表明,本方法可以消除原来存在的表面凹坑,有效地提高最终的表面加工质量。 相似文献