LD Pumped High Efficinet Intracavity Frequency -Doubled Green Laser

A laser diode (LD) pumped Q-swithedh high efficient intracavity frequency -doubled Nd:YAG laser is reported here,The authors have designed and optical and pointed out that the key to increasing harmonic conversion efficiency is to decrease the loss of fundamental wave.In the experiments ,a fundamental mode output laser was acquired,When the pumping power was 12 W ,2.6W average output power at 1064 nm with AO Q-swithc was obtained 2.1 W average output power at 532 nm was obtained with intravity freuency doubling ,and the hihest second harmonic coversion efficiency was 82%.     

Rietveld quantification of γ-C2S conversion rate supported by synchrotron X-ray diffraction images

The pure γ-Ca2SiO4 （]t-C2S） phase was prepared at 1623 K of calcining temperature, 10 h of holding time and furnace cooling. The 13-C2S phase was obtained through γ-C2S conversion with the following calcination system which was adopted at 1473 K of calcining temperature, 1 h of holding time and then water-cooling. The conversion rate of γ-C2S was studied by the Rietveld quantitative laboratory X-ray powder diffraction supported by synchrotron X-ray diffraction images. The refinement results show that the final conversion rate of γ-C2S is higher than 92%. The absolute error of the γ-C2S conversion rate between two Rietveld refinements （sample with or without α-Al2O3） is 3.6%, which shows that the Rietveld quantitative X-ray diffraction analysis is an appropriate and accurate method to quantify the γ-C2S conversion rate.     

Stress and Displacement Distribution of Soft Clay Slope with 2D and 3D Elastoplastic Finite Element Method

Based on elastoplastic model, 2D and 3D finite element method (FEM) are used to calculate the stress and displacement distribution in the soft clay slope under gravity and uniform load at the slope top. Stability analyses indicate that 3D boundary effect varies with the stress level of the slope. When the slope is stable, end effect of 3D space is not remarkable. When the stability decreases, end effect occurs; when the slope is at limit state, end effect reaches maximum. The energy causing slope failure spreads preferentially along y-z section, and when the failure resistance capability reaches the limit state, the energy can extend along x-axis direction. The 3D effect of the slope under uniform load on the top is related to the ratio of load influence width to slope height, and the effect is remarkable with the decrease of the ratio.     

China’s energy price shocks on its tertiary industry energy efficiency: a vector-error-correction model based empirical study

Assuming the heterogeneity of different industries, this paper, using time series data of years from 1980 to 2008 to empirically testify the direct &indirect as well as the long & short term shocks from energy price on energy efficiency of the tertiary industry in P. R. China, concludes that the rise of energy prices can significantly reduce the energy intensity in China’s tertiary industry in the short and long run. Meanwhile, indirectly, energy price increase also exerts strong influence on the tertiary industry energy efficiency via the channel of coal consumption ratio change in the tertiary industry; namely, the higher energy price leads to more coal consumption, thus enhancing the energy efficiency as well.     

Performance of a novel energy-regenerative active suspension system

A novel energy-regenerative active suspension (NEAS) system was designed to solve the problem of low energy recovery efficiency caused by frequent alternation of energy-recovery mode and active-control mode in a traditional energy-regenerative active suspension (TEAS) system. The energy recovery and active control could be implemented simultaneously in the NEAS. The transforming processes and the corresponding computational formulas of power conversion in the NEAS were provided. The simulation results show that the performances of energy recovery of the NEAS are improved, and the self-sustaining of power supply for the NEAS can be realized.     

The permanence of a higher order discrete time system

~~The permanence of a higher order discrete time system@朱伟$Institute For Nonlinear System, Chongqing University of Posts & Telecommunications, Chongqing 400065, P.R. China~~the Technology Research Foundation of the State Ministry of Education (No. 02130)…     

Surface Modification of Cu-Cr Complex by NIR and MIR Laser简

Irradiated by infrared laser, the surface reducibility and adsorbability of Cu-Cr complex could be improved, owing to the interaction of photo-fragmentation and laser texturing. Analyzed by the binding energy spectra and the auger spectra, the valence states of chromium ion and copper ion were+3 and+1 after radiation respectively, which still had the reducibility to release electrons. In contrast with the near-infrared(NIR)1 064 nm and mid-infrared(MIR) 10 600 nm laser at the same average output power of 15 W, the reduced metal percentage in the Cu-Cr complex was obviously distinguished at the depth from nanometer to micron. After chemical plating, the average coating thickness and mean-square deviation of the NIR sample were 11.61 μm and 0.30 for copper layer, and 2.69 μm and 0.08 for nickel layer. The results were much better than those of the MIR sample.     

Experimental Research on Single-Pass SHG from Periodically Poled LiNbO3 Crystal

Quasi-phase-matching(QPM) periodical poled LiNbO3 （PPLN） is designed and successfully fabricated to enable second harmonic generation (SHG),The samples were Z-cut 0.5 mm thick and grating period is A=6.8 μm for the first order QPM of contimual wave λ=1.064μm which is emitted by Nd:YAG laser at room temperature 27℃,The output single-pass SHG power was tested by an authorized optical system.The normalized max conversion efficiency is calculated to be 0.25% (W.cm)^-1,The fabrication and parameters calculated method are introduced,and testing scheme is described in this paper,Even some ideas to improve conversion efficiency are offered.     

Florence,Italy:City of Art,Culture and Soccer

<正>I guess you could say my life began pretty normally. I was born in Indianapolis, Indiana on September 24th, 1982. No big thing at all except for the fact that I was the first son of Terry and Kim Edwards and the first grandson for both sets of grandparents. My life was about to get interesting, and for the next few years it wouldn’t stop spinning.     

Analysis of ice slurry production by direct contact heat transfer of air and water solution

In this paper, a novel system using direct contact heat transfer between air and water solution was proposed to generate ice slurry. The heat transfer process and the system performance were studied; energy efficiency coefficients of 0.038, 0.053, and 0.064 were obtained using different solutions. An empirical relationship between the volumetric heat transfer coefficient Uv and the main parameters was obtained by fitting the experimental data. The Uv calculated from the empirical formula agreed with the experimental Uv quite well with a relative error of less than 15%. Based on the empirical formula, a laboratory-scale direct contact ice slurry generator was then constructed, with practical application in mind. If the air flow rate is fixed at 200 m3/h, the ice production rate will be 0.091 kg/min. The experimental results also showed that the cold energy consumption of the air compressor accounted for more than half of the total amount. To improve the system energy efficiency coefficient, it is necessary to increase the air pipes insulation and the solution＇s thermal capacity, and also it is appropriate to utilize the free cold energy of liquefied natural gas （LNG）.     

Mathematical Analysis of Energy Efficiency in IEEE 802.11 DCF

The standardized IEEE ,802. II distributed coordination function （ DCF） provides a contention-based distributed channel access mechanism for mobile stations to share the wireless medium. However, when stations are mobile or portable units, power consumption becomes a primary issue since terminals are usually battery driven. This paper proposes an analytical model that calculates the energy efficiency of both the basic and the RTS/CTS access mechanisms of the IEEE 802. II protocol. The model is validated with simulation results using NS-2 simulation package. The effects of the network size, the average packet length, the initial contention window and maximum backoff stages on the energy efficiency of both access mechanisms are also investigated. Results show that the basic scheme has low energy efficiency at large packet length and large network size, and depends strongly on the number of stations and the backoff procedure parameters. Conversely, the RTS/CTS mechanism provides higher energy efficiency when the network size is large, and is more robust to variations in the backoff procedure parameters.     

The mechanism of Fe (Ⅲ)-catalyzed ozonation of phenol

Fe (Ⅲ)-catalyzed ozonation yielded better degradation rate and extent of COD (Chemical Oxygen Demand) or oxalic acid as compared with oxidation by ozone alone. Two parameters with strong effects on the efficiency of ozonation are pH of the solution and the catalyst (Fe3 ) dosage. The existence of a critical pH value determining the catalysis of Fe (Ⅲ) in acid conditions was observed in phenol and oxalic acid systems. The best efficiency of catalysis was obtained at a moderate concentration of the catalyst. A reasonable mechanism of Fe (Ⅲ)-catalyzed ozonation of phenol was obtained based on the results and literature.     

Particle Swarm Optimization based predictive control of Proton Exchange Membrane Fuel Cell （PEMFC）

INTRODUCTION Fuel cells have attracted more attention in the last few years due to scarcity of the world energy source. The Proton Exchange Membrane Fuel Cell (PEMFC) is the focus of current development efforts because it is capable of higher power density and faster start-up than other fuel cells (Zhang et al., 2004). Research emphasis is on high power density with adequate energy conversion efficiency. PEMFC performance is related to many factors, among which electrolyte membrane …     

Recovery of Dilute Acetic Acid by Catalytic Distillation Using NKC-9 as Catalyst

The reaction kinetics of dilute acetic acid with methanol using NKC-9 as catalyst was studied at temperatures of 308 K, 318 K, 323 K, 328 K. The kinetic model based on Langmuir-Hinshel-wood rate model was derived and the activation energy was 6.13×104 kJ/kmol. The experiment of recovery of dilute acetic acid was conducted in a packed bed catalytic distillation column. The optimal process parameters and operational conditions determined to make up to 85.9% conversion of acetic acid are as follows:the height of catalyst bed is 1 100 mm, reflux ratio is 4:1, and the ratio of methanol to acetic acid is 2:1. The method can be used as a guide in industrial scale recovery of 15%-30% dilute acetic acid.     

Coupling reaction mechanism of 2-(2-bromo-4-fluoro-phenyl)-1-cyclohexen-1-yl trifluoromethane-sulfonate

The detailed mechanism of CuI-catalyzed C-O intramolecular coupling reaction of 2-（2-bromo-4-fluoro-phenyl）-l- cyclohexen-1-yl trifluoromethane-sulfonate was studied with the density functional theory （DFT）. The geometries of the reactants, transition states, intermediates and products were optimized at the B3LYP/6-31 ＋G＊ level. Meanwhile, the single point energy of species involved in gas and solvent at B3LYP/6-31 I＋G＊ level was individually investigated. Polarizable continuum models （PCM） were applied to the dioxane and water solutions at the same level, respectively. Results show that the rate-limiting step, M3→TS3, does not change in different solutions. However, the activation energy in a dioxane solution is lower than that in water, which explains the previous experimental results. Compared with the non-catalyzed reaction process, the activation energy of the rate- limiting step is reduced by 56.53 kJ mo1-1 in gas and 44.84 kJ mol-l in solvent, demonstrating a high catalytic efficiency of CuI.     

Negative Valve Overlap Mode of HCCI Operation Using Gasoline and Diesel Blended Fuels

The negative valve overlap (NVO) strategy of HCCI operation was experimentally investigated on a gasoline HCCI engine operated with variable valve timing in association with the addition of diesel fuel. The experimental results show that, by using gasoline and diesel blended fuels, the required NVO interval for suitable HCCI combustion under a given engine speed and a moderate compression ratio condition could be reduced, and the HCCI combustion region was extended remarkably without substantial increase in NOx emissions under a given inlet and exhaust valve timing due to the improvement of charge ignitability. In addition, the possible scale of NVO was extended. A substantial increase in the lean limit of excess air ratio and the upper limit of load range can be achieved because of higher volumetric efficiency, resulting from the decrease in the required NVO and the presence of less residual gases in cylinder.     

Synthesis of Dimethyl-2,6-Naphthalene Dicarboxylate by Esterification Catalyzed by Sodium Tungstate

The process of synthesis of dimethyl-2,6-naphthalene dicaboxylate from esterification of 2,6-naphthalene dicarboxylic acid (2,6-NDCA) by methanol using sodium tungstate as catalyst was investigated. The orthogonal tests method was used for optimizing the process factors. The effects of reaction temperature, mass percentage of catalyst, reaction time and mass ratio of methanol to 2,6-NDCA on the 2,6-NDCA conversion were investigated. It was found that all the four factors had significant effect on the conversion. The optimum reaction conditions were reaction temperature 215℃ ,mass percentage of catalyst 356, reaction time 3 h, mass ratio of methanol to 2,6-NDCA 6: 1. The 2,6-NDCA conversion at above condition was 92. 80％.     

Design and Realization of InP/AlGaInAs Multiple Quantum Well Ring Laser

Using beam propagation method(BPM), key optical design parameters of InP/AlGaInAs multiple quantum well(MQW) ring laser were numerically analyzed. The influences of waveguide dimensions, curvature radius and gap size on the coupling efficiency were discussed. An InP/AlGaInAs MQW ring laser with radius of 350 μm was designed and realized. The experimental results show that the designed device, lasing at 1 563.2 nm with side mode suppression ratio higher than 20 dB, exhibited unidirectional bistability between the clockwise and counterclockwise modes.     

Experimental performance of TJR02 as an alternative refrigerant to R22 in a small-scale cold storage

A refrigerant mixture TJR02 was developed and the comparison experiment was performed on a singlestage vapor compression refrigeration system originally designed for R22.Experimental results show that TJR02 can be directly used in the system without modifying the original system or changing lubricant.By replacing R22 with TJR02,cooling rate gets faster and at least 20% of energy is saved.The actual detection in the standard test-bed verifies the experimental results and indicates that the adoption of TJR02 leads to greater efficiency and wider application.And the lower the refrigeratory temperature is,the more obvious the energy saving effects will be.     

Analysis on spectral gain characteristics of PPMgLN based quasi-phase-matching optical parametric amplification

A deep understanding of the spectral gain characteristics of optical parametric oscillators （OPOs） and optical parametric amplifiers （OPAs） is important for a highly efficient optical parametric conversion. We numerically calculated the spectral gain characteristics of a quasi-phase-matching （QPM） parametric conversion process using the periodically poled 6% （mol/mol） MgO doped LiNbO3 （PPMgLN） as the nonlinear crystal. In the simulation we utilized the approach of a transformative matrix of the periodically poled nonlinear medium, which results from the small-signal approximation of three-wave mixed nonlinear equations. Numerical simulation results show that： （1） The full width at half maximum （FWHM） of the spectral gain of the parametric process becomes wider with the increase of parametric wavelength and reaches the maximum at degeneration; （2） The gain coefficient decreases gradually with the increase of parametric wavelength; （3） The spectral gain bandwidth decreases correspondingly with the increase of the nonlinear material length; （4） There exists an optimal parametric wavelength band, which is most suitable for the high gain parametric conversion when pumped by a laser source with a wide wavelength band, such as the high power fiber laser.