Mechanical properties of the take-off leg as a support mechanism in the long jump

The aim of this study was to establish the functions of the support leg in the long jump take-off with a three-element mechanical model spring, damper, and actuator The take-off motions of eleven male long jumpers, with personal bests from 6.45 to 7.99 m, were videotaped at 250 Hz and ground reaction forces were simultaneously recorded at 1 kHz. A two-dimensional 14-segment linked model was used to collect basic kinematic parameters. The spring, damper and actuator forces were determined from the displacement and velocity of the centre of mass and from ground reaction forces. Large spring and damper forces were exerted, and absorbed the impact force immediately after the touch-down. The spring force was also exerted from 25 to 75% of the take-off phase. The actuator force was dominant in the latter two-thirds of the take-off phase. Statistically significant correlations were found between the spring force impulse and the knee flexion during the take-off phase (r = 0.699, p < 0.05), and between the knee flexion and the angular velocity of the thigh at the touch-down (r = 0.726, p < 0.05). These results indicated that the jumper should retain less flexion of the take-off leg knee to increase the spring force, after a fast extension of the hip, and use a more extended knee at the touch-down to prevent excessive knee flexion.     

Determinants of successful R&D cooperation in Japanese small businesses: The impact of organizational and contractual characteristics

Using original survey data on Japanese small businesses, this paper analyses the impact of the organizational and contractual characteristics of cooperative R&D, such as membership structure, partner relationship, external support, and rules of cost and outcome sharing, on the probability of the technological and commercial success of the project. Empirical results suggest that cooperative R&D is more successful, the higher the quality and quantity of external resources available through cooperation, and the lower the transaction and coordination costs required for such arrangements. Moreover, we found that the determinants of technological and commercial success differ considerably.     

碳纤维布约束高强混凝土的研究

基于 8个碳纤维布约束高强混凝土棱柱体试件的试验 ,研究了碳纤维布对提高高强混凝土抗压强度和改善其变形性能的作用 .试验发现 ,包裹碳纤维布可以提高试件的抗压强度 ,并有效地改善混凝土的变形性能 ,其效果随碳纤维用量的增加而更加显著 .在试验基础上 ,根据理论分析和对试验结果的整理 ,归纳出碳纤维布约束高强混凝土的应力 应变全曲线方程 .最后 ,利用提出的全曲线方程编制计算机程序 ,分析了包裹碳纤维布对提高高强混凝土压弯构件的强度和延性的作用     

A quantitative evaluation of the high elbow technique in front crawl

Many coaches often instruct swimmers to keep the elbow in a high position (high elbow position) during early phase of the underwater stroke motion (pull phase) in front crawl, however, the high elbow position has never been quantitatively evaluated. The aims of this study were (1) to quantitatively evaluate the “high elbow” position, (2) to clarify the relationship between the high elbow position and required upper limb configuration and (3) to examine the efficacy of high elbow position on the resultant swimming velocity. Sixteen highly skilled and 6 novice male swimmers performed 25 m front crawl with maximal effort and their 3-dimensional arm stroke motion was captured at 60 Hz. An attempt was made to develop a new index to evaluate the high elbow position (I_he: high elbow index) using 3-dimensional coordinates of the shoulder, elbow and wrist joints. I_he of skilled swimmers moderately correlated with the average shoulder internal rotation angle (r = ?0.652, P < 0.01) and swimming velocity (r = ?0.683, P < 0.01) during the pull phase. These results indicate that I_he is a useful index for evaluating high elbow arm stroke technique during the pull phase in front crawl.     

The continuous measurement of the springboard reaction force in gymnastic vaulting

A new method was established for the continuous measurement of force applied from a springboard to a gymnast in vaulting (board reaction force). Male gymnasts performed a handspring vault using a springboard mounted on force platforms. A high-speed video camera sampled the springboard motion at 500 Hz. The springboard was initially partitioned into 29 segments. The force due to the accelerative motion of the springboard was determined by summing the forces of the individual segments. The board reaction force acting on the gymnast was calculated by subtracting the force due to the accelerative motion of the springboard and weight from the force recorded by the force platform. The new method succeeded in illustrating transient changes of the board reaction force. The horizontal and vertical components of the peak values of the board reaction force were three and two times greater respectively than the average values. A series of tests was conducted to determine whether the number of segments of the springboard model could be reduced without affecting accuracy. A model consisting of only four segments produced almost the same accuracy as the 29-segment model. The simplified model is recommended as a more efficient method to measure board reaction force.     

Impact phase kinematics of instep kicking in soccer

The purpose of this study was to capture the lower limb kinematics before during and after ball impact of soccer kicking by examining the influence of both sampling rate and smoothing procedures. Nine male soccer players performed maximal instep kicks and the three-dimensional leg movements were captured at 1000 Hz. Angular and linear velocities and accelerations were determined using four different processing approaches: processed using a modified version of a time-frequency filtering algorithm (WGN), smoothed by a second-order low-pass Butterworth filter at 200 Hz cut-off (BWF), re-sampled at 250 Hz without smoothing (RSR) and re-sampled at 250 Hz but filtered by the same Butterworth filter at 10 Hz cut-off (RSF). The WGN approach appeared to establish representative kinematics, whereas the other procedures failed to remove noisy oscillation from the baseline of signal (BWF), lost the peaks of rapid changes (RSR) or produced totally distorted movement patterns (RSF). The results indicate that the procedures used by some previous studies may have been insufficient to adequately capture the lower limb motion near ball impact. We propose a new time-frequency filtering technique as a better way to smooth data whose frequency content varies dramatically.     

Primary mechanical factors contributing to foot eversion moment during the stance phase of running

Rearfoot external eversion moments due to ground reaction forces (GRF) during running have been suggested to contribute to overuse running injuries. This study aimed to identify primary factors inducing these rearfoot external eversion moments. Fourteen healthy men ran barefoot across a force plate embedded in the middle of 30-m runway with 3.30 ± 0.17 m · s^–1. Total rearfoot external eversion/inversion moments (Mtot) were broken down into the component Mxy due to medio-lateral GRF (Fxy) and the component Mz due to vertical GRF (Fz). Ankle joint centre height and medio-lateral distance from the centre of pressure to the ankle joint centre (a_cop) were calculated as the moment arm of these moments. Mxy dominated Mtot just after heel contact, with the magnitude strongly dependent on Fxy, which was most likely caused by the medio-lateral foot velocity before heel contact. Mz then became the main generator of Mtot throughout the first half of the stance phase, during which a_cop was the critical factor influencing the magnitude. Medio-lateral foot velocity before heel contact and medio-lateral distance from the centre of pressure to the ankle joint centre throughout the first half of the stance phase were identified as primary factors inducing the rearfoot external eversion moment.     

Ankle taping can reduce external ankle joint moments during drop landings on a tilted surface

Ankle taping is commonly used to prevent ankle sprains. However, kinematic assessments investigating the biomechanical effects of ankle taping have provided inconclusive results. This study aimed to determine the effect of ankle taping on the external ankle joint moments during a drop landing on a tilted surface at 25°. Twenty-five participants performed landings on a tilted force platform that caused ankle inversion with and without ankle taping. Landing kinematics were captured using a motion capture system. External ankle inversion moment, the angular impulse due to the medio-lateral and vertical components of ground reaction force (GRF) and their moment arm lengths about the ankle joint were analysed. The foot plantar inclination relative to the ground was assessed. In the taping condition, the foot plantar inclination and ankle inversion angular impulse were reduced significantly compared to that of the control. The only component of the external inversion moment to change significantly in the taped condition was a shortened medio-lateral GRF moment arm length. It can be assumed that the ankle taping altered the foot plantar inclination relative to the ground, thereby shortening the moment arm of medio-lateral GRF that resulted in the reduced ankle inversion angular impulse.     

The effect of muscle fatigue on instep kicking kinetics and kinematics in association football

The aim of this study was to examine the effect of leg muscle fatigue on the kinetics and kinematics of the instep football kick. Fatigue was induced by repeated, loaded knee extension (40% body weight) and flexion (50% body weight) motions on a weight-training machine until exhaustion. The kicking motions of seven male players were captured three-dimensionally at 500 Hz before and immediately after the fatigue protocol. The significantly slower ball velocity observed in the fatigue condition was due to both reduced lower leg swing speed and poorer ball contact. The reduced leg swing speed, represented by a slower toe linear velocity immediately before ball impact and slower peak lower leg angular velocity, was most likely due to a significantly reduced resultant joint moment and motion-dependent interactive moment during kicking. These results suggest that the specific muscle fatigue induced in the present study not only diminished the ability to generate force, but also disturbed the effective action of the interactive moment leading to poorer inter-segmental coordination during kicking. Moreover, fatigue obscured the eccentric action of the knee flexors immediately before ball impact. This might increase the susceptibility to injury.     

Subsidy and networking: The effects of direct and indirect support programs of the cluster policy

Industrial clusters have attracted considerable attention worldwide for their expected contribution to regional innovation. Recently, policymakers in various countries have developed specific cluster policies. However, there exist few empirical studies on cluster policies. Focusing on the Industrial Cluster Project (ICP) in Japan initiated by the Ministry of Economy, Trade and Industry in 2001, we address two research questions on the support programs of the cluster policies: if the project participants who exploit various support programs are more successful in network formation within the cluster than others, and which kind of support program contributes to firm performance. We pay special attention to the differences between direct R&D support and indirect networking/coordination support. The estimation results, which are based on recent original survey data, suggest that cluster participants who exploit support programs (especially indirect support measures) expand the industry-university-government network after participating in the ICP. Moreover, we find that not every support program contributes to firm performance; firms should therefore select the program that is most aligned with their aims. Indirect support programs have an extensive and strong impact on output whereas direct R&D support has only a weak effect.