Rate-dependent constitutive model of poly（ethylene terephthalate） for dynamic analysis

Uniaxial tensile testing at strain rates ranging from 10-3 to 10-1 s-1 was carried out to study the rate-dependent me-chanical behavior for poly（ethylene terephthalate） （PET） used in the packaging industry. The experimental results show that a rate-dependent plastic behavior exists for PET material. The value of the yield strength was found to increase with the increasing strain rate. A new constitutive model based on the improved Cowper-Symonds rate-dependent constitutive model is proposed to describe the mechanical behavior of PET material in the strain rate ranging from 10-3 to 10-1 s-1, providing more accurate material data for the subsequent simulation analysis of drop test and dynamic buckling. The predictions obtained using the proposed model are compared with experimental results of the improved Cowper-Symonds model. The simulating results of the proposed model agree well with the experimental data. For a low strain rate, the predictions of this model are more precise than those obtained using the improved Cowper-Symonds model. This confirms that the new constitutive model is suitable for describing the me-chanical behavior of PET material at a low strain rate and modeling impact problem.     

Investigation of low-cycle fatigue behavior of austenitic stainless steel for cold-stretched pressure vessels

Cold-stretched pressure vessels from austenitic stainless steels(ASS) are widely used for storage and transportation of liquefied gases,and have such advantages as thin wall and light weight.Fatigue is an important concern in these pressure vessels,which are subjected to alternative loads.Even though several codes and standards have guidelines on these pressure vessels,there are no relevant design methods on fatigue failure.To understand the fatigue properties of ASS 1.4301(equivalents include UNS S30400 and AISI 304) in solution-annealed(SA) and cold-stretched conditions(9% strain level) and the response of fatigue properties to cold stretching(CS),low-cycle fatigue(LCF) tests were performed at room temperature,with total strain amplitudes ranging from -.4% to -.8%.Martensite transformations were measured during the tests.Comparisons on cyclic stress response,cyclic stress-strain behavior,and fatigue life were carried out between SA and CS materials.Results show that CS reduces the initial hardening stage,but prolongs the softening period in the cyclic stress response.Martensite transformation helps form a stable regime and subsequent secondary hardening.The stresses of monotonic and cyclic stress-strain curves are improved by CS,which leads to a lower plastic strain and a much higher elastic strain.The fatigue resistance of the CS material is better than that of the SA material,which is approximately 1?03 to 2?04 cycles.The S-N curve of the ASME standard for ASS is compared with the fatigue data and is justified to be suitable for the fatigue design of cold-stretched pressure vessels.However,considering the CS material has a better fatigue resistance,the S-N curve will be more conservative.The present study would be helpful in making full use of the advantages of CS to develop a new S-N curve for fatigue design of cold-stretched pressure vessels.     

Effect of static magnetic field on α-amylase activity and enzymatic reaction

The effect of magnetic field on α-amylase was studied. Under the experimental conditions, α-amylase solution was treated by 0.15 T, 0.30 T and 0.45 T static magnetic fields for a known period of time, then the activity, kinetic parameters, and the secondary conformation were investigated. The results showed that there was a considerable effect of the magnetic exposure on the α-amylase. The activity was increased by 27%, 34.1%, 37.8% compared with the control. It was also found that both kinetic parameters K _m and V _m could be decreased due to the increasing magnetic field, K _m decreased from 2.20×10^?2 to 0.87×10^?2, whereas V _m decreased from 2.0×10^?3 g/min to 1.1×10^?3 g/min. At the same time, there were some irregular changes in α-amylase secondary conformation.     

Investigation on Zener-Hollomon parameter in the warm-hot deformation behavior of 20CrMn Ti

INTRODUCTION As one of the main forming materials for warm- forging accurate forming technology, 20CrMnTi cemented alloy steel is usually employed in the fab-rication of wearable parts subjected to medium dy-namic load, such as change gear, gear shaft, cross pin end, hub splines, etc., which are extensively adopted in the automobile industry. The application of warm forging technology (Hirschvogel and Dommelen, 1992; Sheljaskov, 1994; Shivpuri et al., 1994; Siegert et al., 1997; Lange…     

Instructional practices in reformed undergraduate STEM learning environments: a study of instructor and student behaviors in biology courses

ABSTRACT

Theoretically, organisational culture, instructor training, and learning space design influence how faculty teach STEM courses. Previous studies have used classroom observation protocols to characterise the range of teaching practices in mostly teacher-centered, traditional STEM classrooms. In this study, we examined the classroom behaviour of 13 STEM faculty teaching biology courses in a reformed undergraduate STEM learning environment. Our findings indicate that instructors teaching in this reformed environment guided student learning (58.4?±?1.9%) almost three times more than they presented information (20.0?±?2.2%). Students worked individually or in groups and talked to the whole class (57.1?±?1.8%) 1.5 times more than they received information (35.5?±?1.9%). We found significant positive correlation between ‘instructor presenting’ and ‘students receiving’ information (r?=?0.743, p?=?1.4?×?10^?4) and ‘instructor guiding’ and ‘student working and talking’ in class (r?=?0.605, p?=?7.2?×?10^?5), suggesting that instructors can change their own classroom behaviours and expect concurrent change in their students’ behaviours. Finally, sequencing teaching practices in high active-engagement classrooms showed instructors move and guide student group work and lead whole class discussions before lecturing to students, which could lead to deeper learning of conceptual knowledge. We discuss insights from these findings that have implications for acculturating evidence-based teaching practices in STEM departments.     

Nb-Ti微合金钢热变形过程中的再结晶和沉淀行为研究

1　Ｉｎｔｒｏｄｕｃｔｉｏｎ　Ｔｈｅｆｕｎｄａｍｅｎｔａｌｐｈｙｓｉｃａｌｍｅｔａｌｌｕｒｇｙｏｆｔｈｅｒｍｏｍｅｃｈａｎｉｃａｌｐｒｏｃｅｓｓｉｎｇ(ＴＭＰ)ｈａｓｂｅｃｏｍｅｍｕｃｈｂｅｔｔｅｒｕｎｄｅｒｓｔｏｏｄｏｖｅｒｔｈｅｌａｓｔｔｗｏｄｅｃａｄｅｓ[1～8].ＩｔｉｓｗｅｌｌｃｏｍｍｏｎｌｙｒｅｃｏｇｎｉｚｅｄｔｈａｔｔｈｅｍｉｎｕｔｅａｄｄｉｔｉｏｎｏｆｓｔｒｏｎｇｃａｒｂｏｎｉｔｒｉｄｅｏｒｎｉｔｒｉｄｅｆｏｒｍｉｎｇｅｌｅｍｅｎｔｓｓｕｃｈａｓＮｂ,ＴｉａｎｄＶｔａｋｅｓｖｅｒｙｉｍｐ…     

石灰岩扩容过程中的物理参数实验研究

利用三轴实验对石灰岩扩容过程中物理参数的实验结果进行分析表明:岩石存在裂纹稳定性传播与裂纹的非稳定性传播和宏观破裂过程;在前期研究三轴实验中横波速度极大值作为岩石应力门槛值的基础上,增添了横波的衰减系数的最小值,即品质因子的最大值作为新的判据;提出了裂纹稳定性传播阶段与裂纹的非稳定性传播阶段分界的特征是:横波的衰减系数、横波损伤因子、泊松比、体积应变曲线在该分界处出现拐点。将其归属于裂纹从局部微裂到宏观贯通时破裂的特征,该分界点处在岩石的应力门槛值与抗压强度之间。此项研究结果具有其广泛的应用价值。     

Study on NO2 absorption by ascorbic acid and various chemicals

INTRODUCTION Nitrogen oxide (NOx) is one of the main air pol- lutants found in the flue gases from chemical and power plants belching acid rain and photochemical smog. Over 90 percent of all man-made nitrogen ox- ides that enter our atmosphere are produced by the combustion of various fuels. Compared with the ad- vanced stage of SO2 gas removal technologies devel- opment, the removal of NOx gases is still in the initial stages of development as roughly 90 to 95 percent of NOx emitted i…     

Environmental damage costs from fossil electricity generation in China, 2000-2003

Electricity consumption increases rapidly with the rapid development of China. The environmental damage costs of electricity generation are very important for both policy analysis and the proper management of the environment. A method was developed in this work to estimate gross environmental damage costs according to emission inventory and environmental cost factors, and to extend the costs from provincial to national level with population density. In this paper, sulfur dioxide (SO2), nitrogen oxides (NOx), particulate matter less than 10 μm in diameter (PM10), and carbon dioxide (CO2) from fossil fired power plants over 6000 kW were selected as index pollutants to quantify the environmental costs of damages on human health and global warming. With the new developed method, environmental damage costs, caused by 3 types of fired power plants in 30 provinces and 6 economic sectors during the years 2000 to 2003, were evaluated and analyzed. It can be seen that the calculated total national environmental damage costs of electricity have rapidly increased from 94930.87×106 USD in 2000 to about 141041.39×106 USD in 2003, with an average annual growth rate of 14.11%. Environmental damage costs of SO2, NOx, PM10, and CO2 are 69475.69×106, 30079.29×106, 28931.84×106, and 12554.57×106 USD and account for 49.26%, 21.33%, 20.51%, and 8.90% of total environmental costs in fossil electricity generation, respectively. With regard to regional distribution, external costs caused by fossil electricity generation are mainly concentrated in the more populated and industrialized areas of China, i.e., the Eastern Central and Southeastern areas.     

Petrological study of the western Iratsu mass from the Sambagawa metamorphic belt, central Shikoku, Japan

The western Iratsu mass, the largest tectonic body in the Sambagawa metamorphic belt, central Shikoku, is mainly composed of epidote amphibolite with minor amounts of eclogite. Systematically, a majority of garnets show bell-shaped chemical zoning of pyrope contents and Mg/(Mg Fe2 ) monotonously increasing outward. The grossular component in zonal garnet increases outwards, maximizes at an intermediate part, and then decreases towards the outermost rim, reflecting a process from increasing to decreasing pressure conditions during the prograde metamorphism. Jadeite contents of omphacite range from 25～20mole% within the cores to 15～10 mole% at the rims, implying a pressure-decreasing process (from 11 × 105 Pa to 8 × 105 Pa). The peak pressure-temperature (P-T) condition of 630～680 ℃ and ca. 15× 105 Pa in the western Iratsu mass is much higher than that of (610±25) ℃ and (10± 1)× 105 Pa of the Sambagawa oligoclase-biotite zone schists. The authors suggest a clockwise P-T-t path for the western Iratsu mass.     

Random quadralinear forms and schur product on tensors

In this work, we made progress on the problem that lr(○×)lp(○×)lq is a Banach algebra under schur product. Our results extend Tonge's results. We also obtained estimates for the norm of the random quadralinear form A:lMr×lNp×lKq×lHs→ C, defined by: A(ei, ej, ek, es)=aijks, where the (aijks)'s are uniformly bounded, independent, mean zero random variables. We proved that under some conditions lr(○×)lp(○×)lq (○×)ls is not a Banach algebra under schur product.     

Molecular variability and evolution of a natural population of tomato yellow leaf curl virus in Shanghai,ChinaXiu-ling YANG,Meng-ning ZHOU,Ya-juan QIAN,Yan XIE,Xue-ping ZHOU简

Tomato yellow leaf curl virus (TYLCV), belonging to the genus Begomovirus of the family Geminiviridae, is emerging as the most destructive pathogen of tomato plants. Since the first report of TYLCV in Shanghai, China in 2006, TYLCV has spread rapidly to 13 provinces or autonomous regions of China. In this study, the molecular variability and evolution of TYLCV were monitored in Shanghai from its first upsurge in 2006 until 2010. Full-length genomic sequences of 26 isolates were obtained by rolling circle amplification. Sequence analysis showed that the intergenic region was the most variable, with a mean mutation rate of 4.81×10^?3 nucleotide substitutions per site per year. Genetic differentiation was found within isolates obtained from 2006, 2009, and 2010, though a linear increase in genetic diversity over time was not evident. Whilst significant parts of TYLCV genes were under negative selection, the C4 gene embedded entirely within the C1 gene had a tendency to undergo positive selection. Our results indicate that a mechanism of independent evolution of overlapping regions could apply to the natural population of TYLCV in Shanghai, China.     

Soup-can Pendulum

In these studies, a vegetable can containing fluidwas swung as a pendulum by supporting its end-lipswith a pair of knife edges. The motion was measuredwith a capacitive sensor and the logarithmic decrementin free decay was estimated from computer-collectedrecords. Measurements performed with nine differenthomogeneous liquids, distributed through six decadesin the viscosity η, showed that the damping ofthe system is dominated by η rather than externalforces from air or the knife edges. The log decrementwas found to be maximum (0.28) in the vicinity ofη = 0.7 Pa s and fell off more than 15 fold(below 2 × 10^-2) for both small viscosity(η < 1 × 10^-3 Pa s) and also for largeviscosity (η > 1 × 10³ Pa s). A simple modelhas been formulated, which yields reasonable agreementbetween theory and experiment by approximating therelative rotation of can and liquid.     

Effects of low dose of ketotifen and chloroquine combination on the infrastructure of chloroquine resistant strain of Plasmodium yoelii

46 inbred NIH mice were infected by chloroquine resistant strain of Plasmodium yoelii. The ultrastructure changes were observed under the administration of ketotifen(10mg·kg⁻¹·d⁻¹) and chloroquine(10mg·kg⁻¹·d⁻¹) combination and one after another respectively. The effect of taking ketotifen and chloroquine combination showed that parasites died rapidly with a few of intermittent membranes and vacuoles. The effect of taking two kinds of drugs one after another showed that there were exceedingly rich membranes, concentric arrangement structures similar to rough endo-reticulum and conspiciously blocking of the formation of food vacuoles.     

Experimental approaches and analytical technique for determining heavy metals in fallen dust at ferrosilicon production factory in Edfu, Aswan, Egypt

In this study aimed to evaluate the pollution extent of metals and nonmetals inside and outside the ferrosilicon production factory in Edfu, Aswan, Egypt, raw materials (quartz, cokes, iron oxides), ferrosilicon alloy, silica fume, dust and suspended dust (at different sites) samples were collected from the factory, and fallen dust samples were collected from outside the factory, horizontally (at different sites and different distance and directions) and vertically (at different floors in the selected buildings). Gravimetric methods, X-ray fluorescence (XRF), flame photometer, wide range carbon determinator and atomic absorption spectroscopy tools were used for elements determination. The results indicating that the fallen dust and its element contents on southern factory walls being higher than those on eastern factory walls may be due to the nature of the dusts and effects of wind force and wind direction. Fallen dust levels in different regions outside the factory were found to be affected by the distance, direction and floors. The nature of dust samples was affected by gravity and the suspended dust in different factory units depended on the work capacity and method of handling materials by personnel in different production units. Silica fume was a complicated problem, had dangerous effect against the workers' health, and was characterized by high concentrations of SiO2(90.6%～93.6%) and heavy metals (Mn, 420.6×10-6～520.3×10-6; Fe, 2354×10-6～2685×10-6; Co, 80.7×10-6～101.6×10 6 and Ni,5.3× 10-6～6.05× 10-6). The TSP (Total Suspended Particulate) levels in all factory units were higher than the recommended air quality value (70 μg/m3) under Egyptian law. The effect of ferrosilicon factory fallen dust on the surrounding regions decreased with increasing distance between the factory and these regions. The suspended dust samples in the factory units and their components greatly exceeded national and international standards, so health and environmental criteria must be enforced on these units.     

Nutritional composition of Pakistani wheat varieties

Pakistani wheat varieties are grown over a wide agro-climatic range and as such are anticipated to exhibit yield and quality differences. It is therefore necessary to investigate the nutritional status of wheat varieties in terms of biochemical and physiochemical characteristics available for food and nutritional purposes in Pakistan. The result shows that wheat grains of different varieties contain a net protein level of 9.15%～10.27%, 2.15%～2.55% total fats, 1.72%～1.85% dietary fibers,77.65×10^-6～84.25×10^-6 of potassium and 7.70× 10 6～35.90× 10^-6 of sodium ions concentration, 0.24× 10^-6～0.84× 10^-6 of phosphorus, 1.44%～2.10% ash, 31.108～43.602 g of thousand grain mass （TGM） and 8.38%～9.67% moisture contents. This study is significant in providing an opportunity to explore the available wheat varieties and to further improve their nutritional excellence and also essential for setting nutritional regulations for domestic and export purposes.     

Isolation and characteristics of Arthrobacter sp. strain CW-1 for biodegradation of PAEs

Isolation of new bacterial strains and recognition of their metabolic activities are highly desirable for sustainability of natural ecosystems. Biodegradation of dimethyl phthalate (DMP) under anoxic conditions has been shown to occur as a series of sequential steps using strain CW-1 isolated from digested sludge of Sibao Wastewater Treatment Plant in Hangzhou,China. The microbial colony on LB medium was yellowish,3～5 mm in diameter,convex in the center,and embedded in mucous externally. The individual cells of strain CW-1 are irregular rods,measuring (0.6～0.7)×(0.9～1.0) μm,V-shaped,with clubbed ends,Gram positive and without any filaments. 16S rDNA (1438 bp) sequence analysis showed that the strain was related to Arthrobacter sp. CW-1 and can degrade PAEs utilizing nitrate as electron acceptor,but cannot mineralize DMP completely. The degradation pathway was recommended as: dimethyl phthalate (DMP)→monomethyl phthalate (MMP)→phthalic acid (PA). DMP biodeg-radation was a first order reaction with degradation rate constant of 0.3033 d-1 and half-life 2.25 d. The DMP conversion to PA by CW-1 could be described by using sequential kinetic model.     

Yangxueqingnao particles inhibit rat vascular smooth muscle cell proliferation induced by lysophosphatidic acid

Objective: To observe the effect of Yangxueqingnao particles on rat vascular smooth muscle cell (VSMC) proliferation induced by lysophosphatidic acid (LPA). Methods: The amount of³H-TdR (³H-thymidine) admixed in cultured rat VSMC was measured and mitogen-activated protein kinase (MAPK) activity and lipid peroxidation end product malondialdehyde (MDA) content of the VSMC were assayed. Results: 1×10⁻⁹, 1×10⁻⁸, 1×10⁻⁷ mol/L LPA in a concentration dependent manner, induced the amount of³H-TdR admixed, MAP kinase activity, and MDA content of the cultured rat VSMC to increase. However, 5%, 10%, and 15% Yangxueqingnao serum preincubation resulted in a decrease of 23.0%, 42.0%, and 52.0% (P<0.01) respectively in the amount of³H-TdR admixed, a decline in VSMC MAP kinase activity of 13.9% (P<0.05), 29.6% (P<0.01), and 48.9% (P<0.01) respectively, and also, a decrease in MDA content of VSMC of 19.4%, 24.7%, and 43.2% (P<0.01) respectively, in the 1×10⁻⁷ mol/L LPA-treated VSMC. Conclusions: LPA activates the proliferation and lipid peroxidation of VSMC in a concentration dependent manner. The LPA-induced VSMC proliferation is related to the activity of MAP kinases, enzymes involved in an intracellular signalling pathway. The results of the present study showed that Yangxueqingnao particles can effectively inhibit LPA-induced VSMC proliferation, MAP kinase activation, and reduce lipid peroxidative lesion. Project (No. 491010-W50339) supported by Chinese Traditional Medicine Administration Bureau of Zhejiang Province, China     

Characteristics of bottom gate a-Si TFT array for AM-OLEDs

The authors have fabricated bottom gate amorphous silicon thin film transistor (a-Si TFT) array using five-step lithography process.The device shows a field effect mobility of 0.43 cm 2 /(V·s),on/off ratio of 7.5×10 6 and threshold voltage of 0.87 V.The instability of a-Si TFT is ascribed to the defect state in the a-Si channel and SiNx/a-Si interface.The present a-Si TFT array with SiN x insulator could be a significant step towards the commercialization of active matrix organic lighting diode (AM-OLED) te...     

Gas Absorption and Mass Transfer in a Pore-Array Intensified Tube-in-Tube Microchannel

A pore-array intensified tube-in-tube microchannel (PA-TMC), which is characterized by high throughput and low pressure drop, was developed as a gas–liquid contactor. The sulfite oxidation method was used to determine the oxygen efficiency (φ) and volumetric mass transfer coefficient (k_La) of PA-TMC, and the mass transfer amount per unit energy (ε) was calculated by using the pressure drop. The effects of structural and operating parameters were investigated systematically, and the two-phase flow behavior was monitored by using a charge-coupled device imaging system. The results indicated that the gas absorption efficiency and mass transfer performance of the PA-TMC were improved with increasing pore number, flow rate, and number of helical coil turns and decreasing pore size, row number, annular size, annular length, and surface tension. The φ, ε and k_La of PA-TMC could reach 31.3%, 1.73 × 10⁻⁴ mol/J, and 7.0 s⁻¹, respectively. The Sherwood number was correlated with the investigated parameters to guide the design of PA-TMC in gas absorption and mass transfer processes.