Effect of Shock Wave on Fabricated Anti-Blast Wall and Distribution Law Around the Wall Under Near Surface Explosion

The loads of shock wave effect on fabricated anti-blast wall and distribution law around the wall were investigated by using near surface explosion test method and FEM.The pressure-time histories and variety law on the foreside and backside of the anti-blast wall were adopted in the tests of variety of different explosion distances and dynamites,as well as in the comparison between the test and numerical calculation.The test results show that the loads of shock wave effect on the anti-blast wall were essen-tially consistent with calculation results using criterion under surface explosion when explosion distances exceed 2 m,the distribution of overpressure behind wall was gained according to variety law based on small-large-small.It is also demonstrated that the peak overpressure behind wall had commonly appeared in wall height by 1.5--2.5 multiples,and the peak overpressures of protective building behind wall could be reduced effectively by using the fabricated anti-blast wall.     

New numerical solution for self-acting gas journal bearings

Taking a small pressure change in the gas film of self-acting gas-lubricated journal bearings into account, the corresponding nonlinear Reynolds equation is linearized through appropriate approximation and a modified Reynolds equation is derived and solved by means of the finite difference method （FDM）. The gas film pressure distribution of a self-acting gas-lubricated journal bearing is attained and the load capacity is calculated. The numerical solution has a better agreement with experimental data than a direct numerical solution for different values of the bearing number. It is of interest to note that the eccentricity ratio, at which the new numerical solution is in better agreement with experimental data, is different when the bearing number is changing. The new numerical solution is slightly larger when the eccentricity ratio is smaller, and becomes slightly smaller when the eccentricity ratio is larger.     

Numerical Simulation of Underwater Explosion Loads

Numerical simulation of TNT underwater explosion was carried out with AUTODYN soft-ware. Influences of artificial viscosity and mesh density on simulation results were discussed. Deto-nation waves in explosive and shock wave in water during early time of explosion are high frequency waves. Fine meshes (less than 1 mm) in explosive and water nearby, and small linear viscosity co-efficients and quadratic viscosity coefficients (0.02 and 0.1 respectively, 1/10 of default values) are needed in numerical simulation model. According to these rules, numerical computing pressure profiles can match well with those calculated by Zamyshlyayev empirical formula. Otherwise peak pressure would be smeared off and upstream relative errors would be cumulated downstream to make downstream peak pressure lower.     

Numerical Simulation of Underwater Explosion Loads

Numerical simulation of TNT underwater explosion was carried out with AUTODYN software.Influences of artificial viscosity and mesh density on simulation results were discussed.Detonation waves in explosive and shock wave in water during early time of explosion are high frequency waves.Fine meshes (less than 1 mm) in explosive and water nearby,and small linear viscosity coefficients and quadratic viscosity coefficients (0.02 and 0.1 respectively,1/10 of default values) are needed in numerical simulation model.According to these rules,numerical computing pressure profiles can match well with those calculated by Zamyshlyayev empirical formula.Otherwise peak pressure would be smeared off and upstream relative errors would be cumulated downstream to make downstream peak pressure lower.     

气瓶爆破测试系统的设计与实现

本文介绍了气瓶爆破测试系统,该系统采用FX2NPLC采集气瓶爆破测试中的水压、水位两路传感器信号,上位机采用VB6.0编程语言开发了与PLC通信检测程序以及测试系统,实现气瓶爆破数据测试、图表的自动记录及打印控制输出。     

Simulation of Airblast Load and Its Effect on RC Structures

In the analysis of a structure subjected to an explosion event, the determination of the blast load constitutes a crucial step. The effect of the blast load on the structure depends not only on the peak shock overpressure, but also the impulse (hence the duration). For structures with a regular geometry, the blast load may be fairly well estimated using appropriate empirical formulae; however, for more complex situations, a direct simulation using appropriate computational techniques is necessary. This paper presents a numerical simulation study on the prediction of the blast load in free air using a hydrocode, with focus on the sensitivity of the simulated blast load to the mesh grid size. The simulation results are compared with empirical predictions. It is found that the simulated blast load is sensitive to the mesh size, especially in the close-in range, and with a practically affordable mesh grid density, the blast load tends to be systematically underestimated. The study is extended to internal blast cases. An example concrete slab under internal explosion is analyzed using a coupled analysis scheme. The internal blast load from the simulation is examined and the response of the RC slab is commented.     

液化石油气钢瓶超装的危险性分析

通过计算 ,阐述了液化石油气钢瓶过量充装存在的巨大危险 ,以引起人们的足够重视     

“材料力学”水平冲击问题的教学思考

在课堂教学中发现,学生难以理解在被冲击物的水平方向上施加冲击物的重力来计算动荷因数。本文研究了不同水平静荷载的施加对冲击问题的影响,推导出水平冲击问题求解的通用公式,证明水平冲击问题与静荷载的施加方式及大小无关。若采用动荷因数法,需选择冲击物自身重力作为被冲击物的水平静载,才可得到教材中的结果。结合国外材料力学教材,介绍了水平冲击问题的另一种求解方法,拓宽了读者求解水平冲击的思路,并给出相应的教学建议。     

合肥市U型钢筋混凝土地道桥的静载分析

U型钢筋混凝土地道桥的受力计算比较复杂,涉及到挡土墙土压力计算的水土分算和水土合算,本文通过大型有限元软件ANSYS,建立U型钢筋混凝土地道桥的有限元模型和力学模型,对其进行三维有限元荷载应力分析。     

全隔爆型氧化锆氧含量分析仪的研制

在石化工业生产中需要测量监控加热炉或裂解炉燃烧排放气体中的氧含量.传统的分析仪为非防爆产品,同时在高温条件下使用需要复杂的采样装置,限制了仪器的使用.针对上述问题,研发了一种全隔爆型氧化锆氧含量分析仪,适用于爆炸性环境条件下各种工业锅炉和加热炉排放气体中氧含量的测量,为石油石化等危险场所的氧含量测量提供了一体化的解决方案.     

基于FTA方法实验室压力容器事故原因分析

该文分析了高校实验室压力容器的类型和使用特点,基于事故树分析法对北京某高校安全工程专业实验室瓦斯气瓶危险性进行了定性分析,得出该事故树的最小割集和最小径集。利用模糊数学方法确定了实验室瓦斯气瓶爆炸基本致因事件的模糊概率,得出顶事件发生概率,并对基本事件重要度进行了定量分析。研究结果认为:实验室瓦斯气瓶爆炸事故发生的主要原因为瓦斯气瓶密封性不良和实验室仪器静电放火。该研究结果对实验室压力容器安全管理对策提供了理论依据和技术指导。     

钢球撞击双层带间隙保护板炸药柱的爆炸分析

采用LS-DYNA3D动力有限元程序对钢球撞击双层带间隙保护板炸药柱的爆炸过程进行了数值模拟分析。分析中采用了流固耦合与动力学接触模式,获得了钢球撞击的临界起爆速度,爆炸产生的峰值压力。研究表明,采取适当的保护措施,炸药制成的部件或装置的安全性能够得到保证。     

挡墙对爆炸冲击波传播影响的三维数值模拟

采用有限元软件AutoDyn,对TNT炸药起爆后爆炸冲击波遇到挡墙时的传播规律进行了三维数值模拟,分析了冲击波遇到挡墙时的反射高压及冲击波的环流汇聚作用。结果表明：冲击波遇到挡墙时将会产生反射高压;在比距离较小时,挡墙迎爆面的最大压力发生在挡墙底部;而随着比距离的增大,压力分布将沿挡墙高度趋于均匀。由于反射的作用,在挡墙前的地面上将会出现高压;当冲击波绕过挡墙时,在冲击波三个方向的绕射汇聚作用下,将会在墙后面一定区域内突然产生局部高压,并且随着传播的继续,这个区域不断的扩大,最后再次形成球面波传播。     

Effects of rarefaction on the characteristics of micro gas journal bearings

Given the definition of the reference Knudsen number for micro gas journal bearings, the range in the number is related to the viscosity of air at different temperatures. A modified Reynolds equation for micro gas journal bearings based on Burgdorfer＇s first-order slip boundary condition is proposed that takes into account the gas rarefaction effect. The finite difference method （FDM） is adopted to solve the modified Reynolds equation to obtain the pressure profiles, load capacities and attitude angles for micro gas journal bearings at different reference K_nudsen numbers, bearing numbers and journal eccentricity ratios. Numerical analysis shows that pressure profiles and non-dimensional load capacities decrease markedly as gas rarefaction increases. Attitude angles change conversely, and when the eccentricity ratio is less than 0.6, the attitude angles rise slightly and the influence of the reference Knudsen number is not marked. In addition, the effect of gas rarefaction on the non-dimensional load capacity and attitude angle decreases with smaller bearing numbers.     

一个关于煤矿瓦斯和煤尘监测与控制的数学模型

煤矿开采比较容易出事故,煤矿事故又主要是瓦斯爆炸和煤尘爆炸.为有效防止事故,必须先结合煤矿的实际观测值对瓦斯和煤尘爆炸的危险性进行定性分析,然后采取必要的安全措施.     

一种新颖的测定分子间势能及普适气体常量R的热学实验装置设计

设计了一种简单的实验装置,可同时测量分子间相互作用的势能和普适气体常量R。其实验曲线符合理论值,误差分析后的补偿曲线所得结果可较为精确地与理论结果吻合。该实验常温下即可进行,且精度较高。该装置可用于课堂教学,有利于学生对热学问题的深入理解。     

论信息时代的专业资料室工作

步入新的世纪，我们走进的是一个变化多端的信息时代。现在我们所面对的是知识爆炸和信息技术的飞速发展。在这个时期，我们要加强资料室的建设，适应时代的要求，更好地发挥资料室在教学、科研中的作用。     

模拟高原水下爆炸特征参数的实验研究

高原地区进行的水下爆破工程,因水体表面气压随海拔的升高而线性降低,其装药爆炸后的特征参数是否发生变化,对爆破施工有重要意义;采用密闭的高压爆炸容器,模拟高原气压条件,对雷管水下爆炸参数进行了实验研究,研究结果表明：在海拔0---4500m范围内随着气压降低,冲击波峰值压力大小与气压无关。冲击波衰减时间却有一定增长,导致比冲击波能微小增大;气泡脉动周期按二阶多项式规律显著增大,仍由于气压随海拔升高丽变小,装药深度处的总静水压力随之降低,使比气泡能微量减小,而爆炸总能量基本不变。     

Decomposition of dimethyl sulfide in a wire-cylinder pulse corona reactor

Decomposition of dimethyl sulfide （DMS） in air was investigated experimentally by using a wire-cylinder dielectric barrier discharge （DBD） reactor at room temperature and atmospheric pressure. A new type of high pulse voltage source with a thyratron switch and a Blumlein pulse-forming network （BPFN） was adopted in our experiments. The maximum power output of the pulse voltage source and the maximum peak voltage were 1 kW and 100 kV, respectively. The important parameters affecting odor decomposition, including peak voltage, pulse frequency, gas flow rate, initial concentration, and humidity, which influenced the removal efficiency, were investigated. The results showed that DMS could be treated effectively and almost a 100% removal efficiency was achieved at the conditions with an initial concentration of 832 mg/m3 and a gas flow rate of 1000 ml/min. Humidity boosts the removal efficiency and improves the energy yield （EY） greatly. The EY of 832 mg/m3 DMS was 2.87 mg/kJ when the relative humidity was above 30%. In the case of DMS removal, the ozone and nitrogen oxides were observed in the exhaust gas. The carbon and sulfur elements of DMS were mainly converted to carbon dioxide, carbon monoxide and sulfur dioxide. Moreover, sulfur was discovered in the reactor. According to the results, the optimization design for the reactor and the matching of high pulse voltage source can be reckoned.     

Waiting to Use a Symbol: The Effects of Delay on Children's Use of Models

To use a symbol to solve a problem, children must achieve representational insight; they must realize that the symbol stands for its referent. Moreover, they must keep this relation in mind as they attempt to use the symbol. The present studies investigated the achievement and maintenance of representational insight. 3-year-olds were asked to use a scale model of a room to find a toy hidden in the room. In Study 1a, children first watched as a small toy was hidden in the model. They then waited either 20 sec, 2 min, or 5 min before attempting to find a similar, larger toy that was hidden in the corresponding place in the room. All children experienced all delay intervals; three groups experienced the delays in different orders. There was a dramatic effect of delay order. The children who experienced the 20-sec delay on their first trial generally performed well throughout the 6 trials, but the children who experienced a 5-min delay first almost always failed to find the toy in the room, even on subsequent trials with shorter delays. Additional studies revealed that the negative effects of the initial long delay could be overcome by providing reminders of the model and its relevance (Studies 2 and 3) or by giving children prior experience in using the model (Study 4). The results indicate that keeping a symbol-referent relation in mind can be difficult for 3.0-year-old children. This research is discussed in terms of the importance of maintaining representational insight.